22800 - 1/16” Diameter Pin Punch

This is the pin punch I use for pushing through our 1/16” diameter pin stock used in the fore stock. A useful tip for you is to round the ends of your pins slightly so that they will ease through the existing hole and not cut through, or punch out chunks of wood on the opposite side. Also, slot your underlugs from front to back, not up and down, to allow the barrel to move when stock and barrel expand and contract due to temperature and recoil.

23300 - 4” Jewelers Saw Frame

This saw frame is provided us by either Swiss Grobet or made by Germany to their typical tough quality control. It is strongly constructed with flat rigid steel frames, hardwood handle and thumbscrew locking vises which allow you a full range of adjustments. Remember that you can sometimes re-use a blade if a break occurs closer to one end. Breaks usually occur from impatience getting the blade too hot! I encourage you to use Swiss made blades. They are by far the toughest and last the longest of any others.

23310 - Jewelers Saw Blade #3

Swiss saw blades .011 Thick, .018” wide – Size #3 extra fine, package of 12.

23320 - Jewelers Saw Blade #2

Swiss saw blades .016 Thick, .025” wide – Size #2 fine, package of 12.

23325 - Jewelers Saw Blade #5

Swiss saw blades - Size #5 coarse, package of 12.

25550 - 1/8” Wide – Straight Inletting Chisel

Made right here in our own shop from tool steel and then heat treated for a durable life in two styles. 6-1/2” long in both bent/offset and standard straight shapes, these chisels are available in four blade sizes per style. Will need a final stoning when you receive them to be razor-sharp.

25560 - 3/16”Wide – Straight Inletting Chisel

3/16" wide inletting chisel

25570 - 1/4” Wide – Straight Inletting Chisel

25580 - 3/8” Wide – Straight Inletting Chisel

25585 - 1/4 bent scraper with handle

25585-1/4" bent scraper with handle.

25586 - 3/8” Bent, Flat Scraper

25586- 3/8" bent scraper with handle.

25590 - 1/8” Wide– Bent Offset Inletting Chisel

25600 - 3/16”Wide–Bent Offset Inletting Chisel

3/16”Wide–Bent Offset Inletting Chisel.

25610 - 1/4” Wide– Bent Offset Inletting Chisel

25620 - 3/8” Wide– Bent Offset Inletting Chisel

3/8” Wide – Bent Offset Inletting Chisel.

32305 - Rawhide Mallet

4 oz. rawhide mallet with 1 1/4" diameter face. Ideal for driving wood chisels or metal gravers.

32330B - Nipple Pick/ Vent Pick Brass *** OUT OF STOCK ***

Our new updated design to an old idea has given this useful tool a touch of class. The pick is encased in the brass (or steel) tube to protect both you, and it, while being carried in your pouch. The flat bottom on the case can be used to nap your flint. The pick is made of spring wire. *** Temporarily OUT OF STOCK ***

32330I - Nipple Pick/ Vent Pick Steel *** OUT OF STOCK ***

Our new updated design to an old idea has given this useful tool a touch of class. The pick is encased in the brass (or steel) tube to protect both you, and it, while being carried in your pouch. The flat bottom on the case can be used to nap your flint. The pick is made of spring wire. *** OUT OF STOCK ***

32340 - Solid Brass Knapping Hammer

Solid Brass Knapping Hammer. 3 5/8" long X 1 5/8" wide.

60005 - 6 Piece 7” File Set

For the folks who need a set of recommended general purpose files. I use these regularly for detailing work on both wood and metal. This set has six different files common to a builders needs: half round, triangular, flat, round, square and warding. It is not all you need, but is an assortment of the most critical small files at a very good price for a quality made set.

60015 - Riffler 10 Piece File Set

Finally! Here is a quality made riffler 10 piece file set you should find on many a builders bench. Most work in building rifles is file work, so learn to like it by taking pleasure in the amount of detail which can be created and added to an otherwise plain part. The secret is always in the files! I am convinced that a selection of the correct “cut” files is a gift from above.

60021 - File card (brush)

File card (file brush. This is used to clean the metal filings out of file teeth-very important in extending the life of your files.

60030 - Wire Looping Pliers

Looping pliers

60035 - Wire Flush-Cutting Pliers

Good starts and finishes can only be achieved with a sharp perfect cut. These pliers cut flush at the end of your run without the chisel end so common to regular side cutters. A fine point lets you cut perfectly to end the run. This latest batch is made in Taiwan but cut very cleanly.