| |
21110I - Johnson Peep Sight Only - iron A well designed, graceful, peep sight with a traditional flair. The sight's screw holes are countersunk to hide the screw heads of the two 6-48 thread MOUNTING SCREWS that ARE INCLUDED. Dimensions are 3 1/2" long X .35" wide and the base is 1/16" thick. Not adjustable for elevation, however, the front screw hole is egg shaped to allow a little bit of side to side adjustment by loosening the screw, moving over, and re-tightening it. There are two sizes of apertures available from Muzzleloader Builder's Supply. The larger is .093 (#21210) for quick target acquisition (or tired eyes), and the smaller .050 (#21200) to limit the field of view for target shooting. Hole spacing is .550". Iron. (Top of barrel to sight center is 7/16").
|
|
|
| |
21115 - Modern adjustable Rear sight This is a modern adjustable rear sight. Most likely made for some sort of semi- auto pistol. It is made to fit a 3/8" dovetail .090 deep. Maximum height from barrel to top of sight is 1/2". Has about 3/16" of vertical adjustment. Has about 3/16" of windage adjustment. The adjustable blade in the rear of the sight is reversible and has a round notch in one side and a shallow square notch in the other. I do not know what these were originally made for and I consider them *pull off's* and some of the dovetails show scratching from being installed in a gun. If you do not care about being original, these could be fit to a muzzleloader to have the convenience of an adjustable sight.
|
|
|
| |
21200 - .050 (Small) Aperture for Johnson Peep Sight .050 (Small) aperture for Johnson Peep Sight with a traditional flair. 7/32 X 40 threads.
|
|
|
| |
21210 - .093 (Large) Aperture for Johnson Peep Sight *** OUT OF STOCK .093 (Large) aperture for Johnson Peep Sight with a traditional flair. 7/32 X 40 threads. *** OUT OF STOCK ***
|
|
|
| |
27570 - Cast Rear Sight3/8” dovetail, 1/2" wide and .400 high above dovetail (Southern Guns).
|
|
|
| |
32320 - Small Sterling Silver Front Sight *** OUT OF STOCK ***Small sterling silver front sight. Dimensions will vary on this sight-average dimensions are 7/16" long, 5/16" wide, 3/16" tall. To be soldered onto round barrels. *** OUT OF STOCK ***
|
|
|
| |
32325 - Milled Rear Sight pistolMilled Tiny Rear Sight This tiny little sight was made with one thing in mind! For pistols where you need to get the sight as low as possible on the barrel. .240 dovetail width. Thick .062 base. Sight measures 1/8" high above the dovetail.
|
|
|
| |
35003 - 5/8” dovetail base .250” high above dovetail Cast Rear Sight
|
|
|
| |
35004 - 3/8” dovetail base .220” high above dovetail Cast Rear Sight
|
|
|
| |
35027 - Tiny front sight blade / blankCast in steel, this tiny front sight can be used as is or as a blank. .090 thick blade x.125 high. .230 dovetail.
|
|
|
| |
35053 - 1” Thin Base – Long .160 high above dovetailCast Rear Sight.
|
|
|
| |
35070 - 1/4Cast Rear Sight
|
|
|
| |
FIBEROPT-G Fiber optic insert in greenFiber optic 1 1/2" long insert in green. Can be used in our #35097 or 35097B front sight.
|
|
|
| |
FS-1-GS - Small German Silver Front SightSmall German silver front sight. Dimensions will vary on this sight-average dimensions are 1/2" long, 5/16" wide, .160" tall. To be soldered onto round barrels.
|
|
|
| |
FS-1803-B - Brass cast front sightNice wax cast front sight made for the 1803 Harpers Ferry rifle but suited for many projects. Blade measures .080 wide x .285 tall. Dovetail measures .375 wide x .062 deep.
|
|
|
| |
FS-1803-I - Iron cast front sightNice wax cast front sight made for the 1803 Harpers Ferry rifle but suited for many projects. Blade measures .080 wide x .285 tall. Dovetail measures .375 wide x .062 deep.
|
|
|
| |
FS-39-B - Cast front sight in brassNice wax cast front sight suited for many projects. Blade measures .093 wide x .400 tall. Dovetail measures .375 (3/8) front to back. Sight base is .645 wide x .062 deep.
|
|
|
| |
FS-39-I - Iron cast front sightNice wax cast front sight suited for many projects. Blade measures .093 wide x .400 tall. Dovetail measures .375 (3/8) front to back. Sight base is .645 wide x .062 deep. Length is 1 5/16".
|
|
|
| |
FS-HEA-B - Brass Heart shaped Front Sight *** OUT OF STOCK ***Brass heart shaped front sight. Dimensions are .550" long, .475 wide, .260 tall. To be soldered onto round barrels. *** OUT OF STOCK ***
|
|
|
| |
FS-HOR-B Horse head front sight in brass Horse head front sight in brass. 7/16" tall, 3/4" long, to be soldered onto a round barrel (with the horse looking at you). You will get the rough casting with the sprew still on it so that you can get a hold of it to clean up and buff it as you wish (see the photo of the same sight in German silver). Made by Terry Jo
|
|
|
| |
FS-HOR-GS Front sight horse head German silverHorse head front sight in German Silver. 7/16" tall, 3/4" long, to be soldered onto a round barrel (with the horse looking at you). You will get the rough casting with the sprew still on it (see the photo of the same sight in brass) so that you can get a hold of it to clean up and buff it as you wish. Made by Terry Jo
|
|
|
| |
FS-HOR2-B Running horse head front sight in brassRunning horse head front sight in brass. The sight is .30 tall with a blade width of .085. The base is 5/16" wide X 1 5/16" long, and it is contoured, to be soldered onto a round barrel. You will get the rough casting with the sprew still on it so that you can get a hold of it to clean up and buff it as you wish. These are cast from an original sight that Terry Jo and Ryan made for one of Terry Jo's guns.
|
|
|
| |
FS-HOR2-GS Running horse head front sight in German silverRunning horse head front sight in German silver. The sight is .30 tall with a blade width of .085. The base is 5/16" wide X 1 5/16" long, and it is contoured, to be soldered onto a round barrel. You will get the rough casting with the sprew still on it so that you can get a hold of it to clean up and buff it as you wish. These are cast from an original sight that Terry Jo and Ryan made for one of Terry Jo's guns.
|
|
|
| |
FS-PA-39-I - Iron cast front sight *oversized*Nice ***Oversized*** wax cast front sight suited for fitting to a barrel that has the dovetail too large for standard front sight.. Blade measures .100 wide x .400 tall. Dovetail measures .465 front to back. Sight base is .465 wide x .125 deep. Length is 1.400".
|
|
|
|
RS-1803 - 1803 Harpers Ferry rear sight 1803 Harper's Ferry rear sight. Dovetail is .695 long and .062 (1/16") deep. Sight is .220 tall with a .535 base width. Fits Harper's Ferry barrels and other barrel 1" or less wide.
|
|
|
|